![]() The bushing automatically accounts for the offset when routing the recess and the inlay, allowing you to use a single template to cut a perfect-fitting inlay. Then, remove the bushing and rout the inlay using the same template. Create your pattern as described previously and rout the inlay recess with the inlay bushing installed on the guide. Inlays can add an attractive element to your work, and using a guide makes the process easy. Attach the template to the stock, position the guide in a hole and plunge to bore the hole. When all of these holes have been drilled, mount a cutter into the router that matches the hole size required in the workpiece. Mark the location of the holes and bore them using a drill that matches the exact outside diameter of the appropriately sized guide. Instead, measure and mark once onto a template. Repeatedly drilling a regularly spaced pattern using a drill or drill press can be tedious, as you have to measure and mark every hole. Use an up cut spiral straight bit and rout the waste in several steps. ![]() Plunge the bit into the stock and carefully rout out the waste. Attach the template to your stock and, using a plunge router, position the guide in the hole. Cut the hole in the template and sand the edge smooth. Establish the required dimensions, draw the shape on your template and then add the offset. You can use a guide to rout a cavity or mortise using a simple template. This will account for the offset otherwise, you would need to make two separate templates. Use an inlay bushing to ensure perfect alignment. Simply make one pattern and then use it to create a mirror image. When joining boards to make a wider surface, you can add some interest to the final piece by using different woods and by joining them using a wavy shape instead of a straight edge. Cut the pattern, sand it smooth and then secure it to the stock with clamps or double-sided tape. Keep your pencil perpendicular to the pattern edge at all times. If your pattern has deep curves you can use a compass or a pencil and a piece of wood that is the same width as the offset in order to draw the pattern. If the shape is relatively straight or, at least, free of any sharp curves, cut the pattern to the exact size and simply shift it by the amount of the offset. Decide which straight bit and guide you will use and calculate the offset (refer to the table above). To do this, draw your pattern exactly to size. By cutting the shape close to the final size, and then using a template and a router to finish the job you get a consistent, smooth edge, which requires little additional work. Edge TrimmingĬreating an interesting edge on tables, cabinet sides or other projects is easy to do with a jigsaw or bandsaw, but you’ll be left with saw marks to sand off. For greater accuracy, keep the same edge of the guide against the template throughout the entire process. Ensure the guide is centered and tighten the router-base screws. Loosen the router-base screws slightly and move the tip up so it’s snug in the guide opening. Insert it into the router and screw the guide onto the router base. To ensure your guide is centered on the bit, use an alignment pin. x 21/32 In.), RA1100 - Interface for threaded template guides (and reducer inserts) that fit into a common 1-3/8 In.When creating a template, make your template either smaller or larger by the offset amount, depending on whether you’re routing outside or inside the template (for example, when doing inlays or mortises). x 17/64 In.), RA1105 - Template guide for large dovetail joints (9/64 In. ![]() RA1126 - Quick-release template guide adapter, RA1103 - Template guide for small dovetail joints (9/64 In. counter-bore, such as those sold by Porter-Cable® and others, Case x 21/32 In.), RA1100 - Interface for threaded template guides (and reducer inserts) that fit into a common 1-3/8 In. steel pin that chucks into your routers collet. This is critical for accurate routing when using your router in a hand-held application. MRC23EVSK, MRF23EVS, MRP23EVS, 1613AEVS, 1617-, 1618- and 1619-Series Routers Base Plate Alignment Kit (115-040) This kit works with any router baseplate that accepts Porter-Cable-style template guide bushings to ensure that the baseplate is centered on the router. counter-bore, such as those sold by Porter-Cable® and othersĩ/64 In. RA1100 - Interface for threaded template guides (and reducer inserts) that fit into a common 1-3/8 In. RA1105 - Template guide for large dovetail joints (9/64 In. RA1103 - Template guide for small dovetail joints (9/64 In. RA1126 - Quick-release template guide adapter
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |